Metal Cloak Weld On "DB3" Rear Control Arm Correction Bracket, Jeep JK Wrangler

Skip to product information
Regular price $159.00
Sale price $159.00 Regular price
Shipping calculated at checkout.

Want it installed?

Our techs can fit it at the shop in Vancouver, WA. Book an install or call (360) 440-6375.

The MetalCloak Jeep JK Weld On "DB3" Rear Control Arm Correction Bracket System is the best solution to convert your long arm system back to a mid-arm setup.

Features Include:

  • Fits 2007-2018 JK Wrangler & Wrangler Unlimited
  • 3/16" Steel
  • CAD Designed
  • Laser-Cut
  • Ready To Be Welded
  • Fixture Spacers Included
  • Angled for Approach & Departure
  • Trail-Tested Built-In Skid Plate
  • Raw Metal Finish
  • Made in the USA
The MetalCloak DIY weld-on bracket allows for you to convert your rig back to a mid-arm setup and re-positions the rear control arms to operate within a corrected radius. This system drastically reduces the feel of bump-steer/axle steer on lifted Jeeps and provides handling characteristics comparable to, if not better than, a stock-height Jeep.

The Weld-On DB3 welds directly to the stock location of the factory rear control arm frame brackets that were cut off when installing a long arm kit. The weld-on DB3 allows you to fully weld the bracket to the frame and is angled for approach and departure when off-roading. The weld-on DB3 comes with fixture spacers that allow you to adjust the parts perfectly to the frame so you know the bracket is aligned when welding.

Feel the improvement in acceleration, braking, climbing, and steering performance with the DB3. The DB3 is only available from MetalCloak.

Note: This alignment bracket is designed to be used with adjustable rear control arms. Not to be used with stock control arms.

Note: This is a weld-on DIY product. Do not purchase this product unless you are prepared to weld onto your Jeep.

Note: Builder Parts are intended for your own custom application. There is no implied warranty or instructions for the use of these products; if using any of the builder parts you should be confident of your mechanical skill level and know that you will use at your own risk.



VIDEOS

MetalCloak's Jeep Wrangler Suspension

What is Corner Travel Index?

Since 2014, MetalCloak has tested thousands and thousands of rigs at events all across the country collecting specs on the build and cataloging the results. The data collected allows us to make our own products better.

FMVSS 126 Compliant

MetalCloak not only has the best off-road flex, but we are also Federal Motor Vehicle Safety Standard 126 certified and compliant. No other company can match our on- and off-road performance.

Proudly Made in the USA

MetalCloak proudly manufactures products in America. Take a glimpse of our incredible team that lives and breathes innovation and quality.

THE TECH

Rear Control Arm Correction Bracket "DB3"

Diagram showing a Jeep suspension with a 5.5" lift and 37" tires at full droop, comparing the DB3 to a typical long arm hang-up point.

Green line shows DB3 and how it tucks behind the wheel for optimal approach.

Red line shows a "typical" long arm hanging up MUCH farther forward, increasing the chance for hang-up.

The DB3 provides superior control arm angles for a better ride AND provides better approach angles over a rear long arm in a simple weld-on application.

Correction Bracket Geometry

This product adjusts the roll center of your Jeep, and corrects the geometry of the control arms enabling the full use of up and down travel.

The entire DIY bracket assembly gets welded together for incredible strength, has built-in approach skids, and all surfaces are angled to keep from catching on obstacles. Installs where the factory control arm mounts were located.

Close-up of a raw welded DB3 mounted to the rear control arm locations on a Jeep frame.

Fixture Alignment Spacers

Weld-on bracket mounted on the frame with fixture spacers aligning the parts, with white arrows pointing to both spacers.

The weld-together weld-on DB3 comes with fixture spacers that allow you to adjust the parts perfectly to the frame so you know the bracket is aligned when welding.

What Does It Do?

Adding this system improves rear control arm geometry and adjusts rear axle caster for lifted JK Wranglers. The flatter the control arms are the better; the benefits are immediately felt with a smoother ride and stable handling as the roll center has been adjusted. Braking performance also improves, maximizing safety along with the comfort and performance of your Jeep JK Wrangler.

Animated diagram of a Jeep rear suspension comparing control arm angles with and without the DB3, highlighting the smoother ride with the DB3.

What's in the Kit?

  • DB3 Correction Bracket
  • Bracket Spacers
  • All Required Hardware
Contents of the MetalCloak JK Wrangler Weld-On DB3 Rear Control Arm Correction Bracket kit, including the DB3 correction bracket, bracket spacers and all required hardware.

TECHNICAL SPECIFICATIONS



Items Details
Compatibility 2007-2018 JK Wrangler & Wrangler Unlimited
Drop Bracket 3/16" Steel Sheet
Coating Raw


IMPORTANT NOTES



Control Arms: This alignment bracket is designed to be used with adjustable rear control arms. Not to be used with stock control arms.

Weld-On Product: This is a weld-on DIY product. Do not purchase this product unless you are prepared to weld onto your Jeep.

Builder Parts: Builder Parts are intended for your own custom application. There is no implied warranty or instructions for the use of these products; if using any of the builder parts you should be confident of your mechanical skill level and know that you will use at your own risk.

INSTALLATION



Difficulty Difficult
Body Modification Welding
Time to Install 5-6 Hours


Fitment & Specifications

Brand Metal Cloak
Product Type Control Arms & Links
Vehicle Fitment Jeep Wrangler JK
Part Number 7696
Metal Cloak Weld On "DB3" Rear Control Arm Correction Bracket, Jeep JK Wrangler

$159.00

Questions about this part?
Call the shop.